|
|
|
Harness
Pads
Part #11564
Racer Net. $24.95
Harness Pads Made with Flame Retardant Material
Part Numbers for other
colors available:
11562/Red, 11563/Blue |
|
|
Also
Available
Racer Net Sewn on
Harness Pads
$17.95 Part #pads
Available in 2" &3"
Red, Blue,
Black, Purple, Gray,
Not Flame Retardant |
|
 |
|
Arm
Restraints #11572
Racer Net. $24.95
Arm Restraints Made with Flame Retardant Material
Part Numbers for other
colors available:
11573/Blue, 11574/Black |
|
|
|
Mounting Hardware |
|
|
|
 |
Floor
Mount Snap, Eye Bolt Nut & Washer
Part #11546
Racer Net $6.46
1 Each Per Set |
|
|
|
|
|
|
|
|
|
Bolt
In Bracket
Part #11549
Racer Net $4.29
2 Each Per Set |
|
|
|
|
|
|
|
|
|
2"
3-Bar Slide
Part #11551
Racer Net $3.95
2 Each Per Set |
|
|
|
|
|
|
|
|
|
Eye
Bolt Nut & Washer
Part #11548
Racer Net $6.43
2 Each Per Set |
|
|
|
|
|
|
|
|
|
3"
3-Bar Slide
Part #11547
Racer Net $5.72
2 Each Per Set
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
Tension
Springs
Part #11550
Racer Net. $10.00
Tension Springs for Seat Belt & Harness
Sold in Sets of Four |
|
|
|
|
|
|
|
|
Note:
Springs hold the tension on the adjustment bar against the
belts. |
|
|
|
|
|
Helmet
Restraints
Part #11602, Racer Net $7.50
Part Numbers for other colors available:
11603/Blue and 11604/Black
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Nomex
Double Layer Gloves
Part #11724
Racer Net. $49.95
Sizes Small, Medium, Large
&
Extra Large SFI5
Specify size and color, Red, Blue
or Black |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
Neck
Collars
Part #20162
Racer Net. $24.99
360 degree Neck Collar
Part Numbers for other
colors available: 20163/Blue, 20164/Black
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Installation
Tips
These lap belts and shoulder harnesses
meet or exceed the revised SFI 16-1 Military Specifi-
cations. Useful life of the webbing should not exceed two years and is
recommended that they be replaced at or before that time.
If involved in an accident or the
webbing shows wear or abuse, return to the manufacturer for inspection
or replacement. All hardware on lap belt, harness and anti-submarine
belts are not to be welded on, bent or straightened as this will cause
fracture. |
|
|
|
|
|
|
|
|
|
All mounting brackets must be
installed at an angle that is compatible with the direction of the pull
on the webbing under full load.
Mounting brackets must be attached directly to the frame or chassis. Do
not mount to sheet metal or floor boards.
Seat belts should be anchored apart, the width of the driver.
Seat belts should be anchored at a 45 degree angle to the floor. See
drawing.
Anti-submarine belts should be anchored behind the chest line.
Always use grade 8 bolts, nuts and washers for driver restraint
installations.
All hardware used to manufacture these driver restraints are
manufactured in sheet alloy steel and drop forged alloy steel. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE:
Hardware on the ends of the lap
belt that attaches your belt assembly to the floor area must be mounted
in a vertical position. Shoulder harnesses and lap belts must be mounted
vertically. |
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Home